Open the PPE Cabinet Before You Restart: A Five-Step Post-Holiday Equipment Check
Time of issue:
2026-10-07 12:46
Origin:
【Summary description】
October 6, the day before work resumes. In front of the PPE cabinet in a corner of the warehouse, storekeeper Xiao Chen, logbook in hand, works with Lao Zhou to open the cabinet doors one compartment at a time. Safety helmets are stacked three high, the goggle boxes have gathered a thin layer of dust, and a few pairs were shoved back in carelessly after the last rush job.
Lao Zhou says: "When we start tomorrow, the first job isn't switching on the machines. It's going through this cabinet. The equipment had a holiday, but the risks didn't."
This "health check" has a basis in the standards. Clause 5.3.1 of GB 39800.1-2020 Specification for the Equipment of Personal Protective Equipment, Part 1: General lists the situations in which equipment must be scrapped and replaced: it fails inspection, it has passed its expiry date, its function has been lost, and so on. The holiday is the ideal window for a concentrated check. Swapping in new equipment before work resumes takes thirty seconds; an incident after work resumes carries a cost that cannot be calculated.
The check also has a preliminary step: look at storage. How long equipment lasts depends not only on how long it has been used, but also on the cabinet it lives in. Rubber parts suffer from sunlight and heat, so on shelves where the sun reaches, helmet harnesses and rubber seals age far faster than the ledger suggests. Damp corners make leather gloves go mouldy and filter cartridges absorb moisture. In compartments shared with paints and solvents, rubber parts swell from the fumes. So before opening the cabinet, inspect the cabinet itself: anything stored in the wrong place gets moved first, then checked.
The check has five steps. Take them one at a time.
Step 1: Check the dates. Look at expiry first
All equipment has a service life. Filter cartridges for air-purifying respirators, lenses for welding face shields, and any consumable marked with a production date and shelf life: check the date before anything else. "Past its expiry date" in Clause 5.3.1 is a hard line. Expired items, however new they look, should go through the scrapping procedure rather than being "made to do for a while longer."
Xiao Chen added an "Expiry Date" column for each compartment in the logbook. Now, simply opening the book shows which compartment is about to reach its date, without waiting for the next check to find out.
Step 2: Inspect the exterior. A one-millimetre scratch is still a defect
For safety helmets, check three things: whether the shell has cracks or dents from knocks, whether the harness has come loose, and whether the chin strap is still sound. The shell is the load-bearing outer component. If it is cracked, replace the whole helmet; there is no such thing as "it's cracked at the back, so it doesn't matter."
For goggles and face shields, check the lenses. Clause 8.6 of GB 14866-2023 General Technical Specification for Eye and Face Protectors counts scratches, cracks and mould spots within a 30 mm radius of the lens centre as surface defects. Do not underestimate a one-millimetre scratch: it bends the apparent path of flying particles in your vision, and the effect is especially noticeable in low light on night shifts. Clause 7.1 of the same standard specifies that for eye and face protectors without a filtering function, luminous transmittance at the reference point shall be no less than 85%. Old lenses that have yellowed with age may already have quietly fallen below this line.
For gloves, check the palms and fingertips; for safety shoes, check the anti-slip tread on the soles and the toe caps. Anything peeling, delaminating or worn through goes straight into the scrap bin.
Step 3: Test the function. It only counts once it is worn
Passing the visual inspection is only the minimum; function has to be tested hands-on. Clause 3.2 of GB 39800.1-2020 requires that equipment be suited to the working conditions, the hazard factors and the degree of hazard, and that it fit the worker. The same pair of goggles may seal perfectly on one worker and leave gaps on another, in which case the protection exists only on paper.
Test three things: whether the goggles fit the face without gaps and whether the vents are still clear; whether the face shield's clips and headband tension are right and whether it flips up and down smoothly; and whether the helmet's harness holds the head when the helmet is worn and turned. Where possible, test emergency facilities such as eyewash stations and emergency stop buttons at the same time. They have also been "on holiday" for a week, and only running water through them will show whether nozzles are blocked or valves are stiff.
Step 4: Match the scenario. Match models to the job, not to the stock
The most common mistake in the check is issuing whatever is in the cabinet. The right approach is to issue whatever the job requires.
Clause 8.3 of GB 14866-2023 divides high-speed particle impact performance into three grades: low energy at 45 m/s, achievable by spectacles, goggles and face shields; medium energy at 80 m/s, achievable only by goggles and face shields; and high energy at 120 m/s, achievable only by face shields. So next to grinders and cutting machines, issue the full set of helmet plus face shield plus goggles, and do not rely on spectacle-type eye protection against high-speed spatter.
Welding positions have their own set of numbers: under Annex G of GB 3609.1—2025 (mandatory, effective September 1, 2026), shade numbers 8 to 14 are selected for manual arc welding, and 1.2 to 4 for welding assistants. Welding helmets, welding gloves and flame-retardant workwear: none of them can be missing.
Where several types of equipment are issued together, also check against Clause 3.4 of GB 39800.1-2020: when equipment is issued in combination, compatibility and functional substitution shall be considered. If a face shield and goggles press against each other and push the lens out of position, protection is compromised.
Step 5: Update the records. Make the next check traceable
The check is not finished when the cabinet door is closed. Three things go into the book: an equipment issue confirmation form, recording who is going on duty, which model they received and whether the trial fit was good, with a signature; a spare-parts list, keeping one complete new spare set each of goggles, face shields, helmets and filter cartridges that can be issued as full sets by scenario; and a scrapping record, noting the reason and date for each item replaced so that it does not find its way back into the cabinet.
Three of the most common pitfalls
Pitfall 1: "It looks new, so there's no need to replace it." The hard line of the expiry date does not care about appearance. An expired filter cartridge protects about as well as wearing nothing.
Pitfall 2: "Scratches don't affect use." The surface-defect requirement in Clause 8.6 is not a cosmetic clause; it is an optical performance clause.
Pitfall 3: "As long as the spares cabinet has stock, we're fine." Spares must be stocked as complete sets matched to job scenarios. If you cannot put together a full set when it matters, you effectively have none.
Things you can do today
1. Assign the five-step PPE cabinet check to named people, finish it today, and issue fresh equipment directly when work resumes tomorrow.
2. Add an "Expiry Date" column to the logbook and flag equipment one month before it expires.
3. Keep the scrap bin separate, log replaced equipment on the same day, and do not let it flow back.
4. At the pre-shift meeting, hold up two pairs side by side: one brand-new and compliant, one with scratches beyond the limit, so everyone can see the one-millimetre difference.
Equipment is the last line of defence, and that line cannot go on duty damaged. How often does your plant check its PPE cabinet? Share in the comments, and in the next issue we will put together a template for the equipment issue confirmation form.
This article is compiled from current standards, laws and regulations. The original text of the standards and your organisation's own rules shall prevail.
Related Products

010-86460988
在线留言